PrimaCreator FlexPlate-Powder Coated PEI 235 x 235 mm
- Item Id 25051
- Variation ID 6148
- EAN 7340002117836
- Mfg part No, PC-FPPC-235/235
The Flexplate-Powder Coated PEI is the perfect surface to print on, it’s very durable and easy to manage. And best of all, thanks to the Flexible plate your prints will be very to remove. Just give it a small bend and the print will pop right off.
Why should I use PrimaCreator FlexPlate-Powder Coated PEI?PrimaCreator FlexPlate-Powder Coated PEI
The new Powder Coated FlexPlate from PrimaCreator consists of three parts. The first one is the magnetic surface that you will attach to the printers bed. The second and third one is the high quality spring steel sheet that is covered with a sheet of the best PEI Ultem .
The Flexplate-Powder Coated PEI is the perfect surface to print on, it’s very durable and easy to manage. And best of all, thanks to the Flexible plate your prints will be very to remove. Just give it a small bend and the print will pop right off.
PrimaCreator FlexPlate-Powder Coated PEI is based on a ferrit core which is much more heat resistant than neodymium magnets. This FlexPlate can withstand temperatures up to 130°C without any problems, so you can even use it with ABS.
PEI Ultem (Polyetherimide) from PrimaCreator is a reusable, relatively maintenance free, build surface for both ABS (with a Heated bed) and PLA (hot or cold), other materials such as Metal, Wood, PETG, ABS+ and many others also works just fine. You don’t require any additional adhesives such as glue or tape. PEI is appealing due to its "no-surface-prep" conditions, which make it convenient to work with. Additionally, printing on PEI requires no support rafts as parts adhere directly to the surface with no issue.
How To Use.
Unpack your FlexPlate, attach the magnetic surface to your print bed and then attach the spring steel plate with the PEI attached to it onto the magnetic surface. Remove the protective film from the PEI and re-level your print bed. You are now ready to print away. Parts should come free from the surface with almost no issue at all. PLA does not require heat but turning the heated bed up to 45C helps. You don´t need any adhesives but if you are going to print something large or for a long time, we recommend using the PrimaFix adhesive stick, it will make your parts stick even better and release even easier when the print is done. After the print is done, just let the plate cool down, remove the plate and give it a gentle bend. You can then just “pop” the model off the plate. Before each print, wipe your PEI surface down with 70-91% Isopropyl alcohol, to ensure that you wipe away any grease or other residues that may have accumulated on the surface. This will help increase your surface adhesion greatly. Use acetone, isopropyl alcohol, methyl alcohol, or soap to clean your PEI after use.
Bra Produkt!
Har testat denna ett par veckor nu och är mycket nöjd. Blir en ganska lätt byggplatta viktmässigt vilket har många fördelar. Saknar som flera andra att kunna köpa bara plåten utan magnetskivan.
Christian J.
Otroligt bra för ABS
Jag har bara använt denna för ABS men har inget annat än gott att säga om den, otroligt bra vidhäftning även utan brim. Jag har 90 grader på bädden. Önskar den fanns i 120x120 till min Voron V0.1 (som skrivits ut på denna)
Magnus O.
Utmärkt produkt
Jag är så himla nöjd med denna byggplattan, att ta bort hela byggplattan när du är klar och bara böjja lite försiktigt och utskriften ploppar bort, utmärkt! Vet inte om det min sensor som ger annorlunda värden men jag var tvungen att skruva upp värmen på byggplattan till 80grader för att få PETG att fastna ordentligt. Jag använder PRIMAFIX ihop med denna produkt. Rekommenderas.
Christian L.
Funkar utmärkt, men jag hade...
Funkar utmärkt, men jag hade den gamla versionen som var helt platt utan mönster och på den fick jag finare bottenyta.. och jag tycker de känns lite onödigt att de skickar med en ny magnetskiva varje gång? hade varit underbart om man kunde köpa en utan magnetskiva och kanske till lite lägre pris..
Christoffer H.
Probably the best printing surface...
Probably the best printing surface ever. I'm not joking, everything sticks to it like on super glue, but as soon you are done, you can remove the print with ease just by flexing it. And most importantly, you can do it off of the bed, and not mess up your levels. Installed on Creality Ender 3 V2.
Robert N.
1000 ggr bättre än vad...
1000 ggr bättre än vad som kommer med en Creality Ender 3 pro. Har inte haft en enda "warping" sedan jag började använda denna. Fastnar varje gång. Lossnar jätte lätt när man är färdig.
Sebastian K.
två sidor!(?)
Verified purchase
PEI-plattan som jag fick levererad idag skiljer sig från Primas platta som jag hade köpt redan 2019 fast alrdig använt till min tidigare skrivare. Den äldre modellen hade bara en PEI-yta och den var slät. Plattan jag fick idag har båda sidor täckta med PEI, framsidan är som ett medelgrovt sandpapper, relativt lik byggplattan som följde med min Anycubic Kobra Neo. Men baksidan är helt slät som den tidigare modellen och fungerar utmärkt med PLA. Eftersom den dubbla sidan inte marknadsförs aktiv så vet jag inte om det är bara mitt exemplar eller om man kan lita på det vid nästa beställning.
Uwe Z.